არასტანდარტული flange DN8-DN4000

არასტანდარტული ფლანგი

Non-standard flanges will only be used in cases where pressure, temperature and size requirements exceed the capabilities of standard flanges. Keep in mind that non-standard flanges require calculation, design and special manufacturing procedures, which is why they are chosen only as a last resort. The most common such applications are large equipment flanges and heat exchangers body flanges.

Non-standard flanges are designed and calculated according to ASME VIII Div.1 Appendix 2 and Appendix S, and according to ASME VIII Div.2 part 4.16.

Design criteria
Rules for the design of bolted flange connections as described in Div.1 Appendix 2 apply to flanges with gaskets placed entirely within the circle enclosed by the bolt holes and with no contact outside this circle.

This method is applicable to circular flanges under internal pressure and takes into account only hydrostatic end loads and gasket seating loads. Rules have been further modified so that they can be applied to the design of flanges under external pressure, reverse flanges and flanges with nut stops.

Design procedure for large diameter, low pressure flanges shall be supplemented by methods other than the code e.g.: check flange rotation. Flanges greater than 60 inches (1524 millimeters) inside diameter and designed for up to 100 psig (689 KPa) pressure fall under this category.

 

ზომა

არასტანდარტული ფლანგური: 1/4 ″ -160 ″

DN8-DN4000

მასალა:

ნახშირბადოვანი ფოლადი: ASTM A105, ASTM A105N, GB 20, C22.8.

დისკები: ASTM / ASME A182 F1-F12-F11-F22- F5-F9- F91

უჟანგავი ფოლადი: ASTM / ASME A182 F304-304L-304H-304LN-304N

ASTM / ASME A182 F316-316L-316H-316LN-316N-316Ti

ASTM / ASME A182 F321-321H, F347-347H

დაბალი ტემპერატურის ფოლადი: ASTM / ASME A350 LF2.

მაღალი ხარისხის ფოლადი: ASTM / ASME A694 F42, F52, F56, F60, F65, F70

 

Flange მოსაპირკეთებელი ტიპი

ამერიკის სერიები: ბრტყელი სახე (FF), ამაღლებული სახე (RF), ენა (T), ღარი (G), ქალი (F), კაცი (M), ბეჭის ტიპის სახსრების სახე (RJ / RTJ)

ევროპული სერიები: ტიპი A (ბრტყელი სახე), ტიპი B (ამაღლებული სახე), ტიპი C (ენა), ტიპი D (ღარი), ტიპი E (შპიკი), ტიპი F (ჩაღრმავება), ტიპი G (O-ring spigot), ტიპი H (O-ring Groove)

წნევა

ამერიკის სერიები: კლასი 150, კლასი 300, კლასი 600, კლასი 900A, კლასი 1500, კლასი 2500.

ევროპის სერიები: PN2.5, PN6, PN10, PN16, PN25, PN40, PN63, PN100, PN160, PN250, PN320, PN400.

სტანდარტული

ჩვენი არასტანდარტული ფლანგის დამზადება შესაძლებელია საერთო სტანდარტის საფუძველზე და გარკვეული ცვლილებების შეტანა ჩვენი მომხმარებლების მოთხოვნების შესაბამისად.

ASME ANSI B16.5, ASME ANSI B16.47.

API 605, API 6L.

MSS SP 44

CSA Z245.12

EN1092-1, EN1759-1.

DIN2630, DIN2631, DIN2632, DIN2633, DIN2634, DIN2635, DIN2636, DIN2637, DIN2638.

BS1560, BS 4504, BS 10.

AFNOR NF E29-200-1

ISO7005-1

AS2129

JIS B2220

UNI 2276. UNI 2277.UNI 2278 .UNI 6089 .UNI 6090

სამრეწველო პროცესები

გაყალბება, დამუშავება.

განცხადება არასტანდარტული ფლანგისთვის

ბუნებრივი აირი, ქიმიური ნივთიერებები, ნავთობი, გემების მშენებლობა, საზღვაო ნაწარმი, ქაღალდის დამზადება, მეტალურგია, ელექტროენერგია, ელექტროენერგია, საქვაბე და ა.შ.

 

 

 

,